• Description
  • Technical Data
  • Documentation
  • Programs
  • Available accessories

The QUANCOM® USBOPTO64IN board has 64 optical isolated inputs and is designed for industrial purposes.

Optocouplers protect inputs up to 500 Volts
Your personal computer is protected against damage in case of overvoltage by galvanic isolation. These optocouplers are designed as alternating current optocouplers which means that you can choose the polarity of input signals optionally .The input voltage range is adaptable because of a restistance network plug-in. Feel free to tell us about your requirements concerning the input voltage range in your order.

Input state changing
The 64 inputs are equipped with input flip-flops which detect quick input state changes or remove switch bounce.

Other features
USBOPTO64INVB example
VB USBOPTOREL32 example
ZoomThe USBOPTO64IN example shows the programming with Visual Basic
Each single port of an USBOPTO64IN opto/relay module is equipped with LEDs for optical function controls which enables to show changes of output or input levels.
You can see the module state through a configuration LED, i.e. intitialisation of the operating system, reading or writing accesses or non-evaluated input edge changes are shown. Through simple assembly in a rack you can use the attachement as a standalone equipment in the laboratory area or as a mobile equipment for a notebook anytime. The current supply occurs either through an external adapter or through an USB bus. The double stick strips for the inputs complete the flexibility of the module.You don't need any knowledge in driver development. We implemented a command set which is compatible for all operating systems.

Additional Features

As all USB Optocoupler Relaymodules each channel has its own optical indicator through a LED. Through 4 additional Status-LEDs the state of the module is allways readable.

By mounting the module on to a top-hat rail the installation is very simple. You may order the needed rail in our shop, too.
An external 12V to 30V power supply is not needed to operate this module, but recommended. Also these power supplies may be ordered at our house. You may choose between our 12V/3A or 24V/2A.

Several modules of the same type are applicable:
You can use up to 16 modules at the same time with the help of a DIP switch, so you can choose a module adress between 0 ... 15. The software is able to identify each module trough the module adress.

Software support
The USBOPTO64IN module is supported by the QLIB (QUANCOM Driver Library) and allows you a simple programming under Windows 7 / Vista / XP / 2000 / Server 2k-2008 R2 / NT 4.0 / 95 / 98 / ME / 3.11, Agilent VEE and Labview. There is no annoying installation of the drivers necessary because of the software port QLIB.
You don't need any knowlege of driver installation anymore. With QLIB you can easily create applications with Visualstudio.NET, Visual Basic, Visual-C, Borland Delphior other compilers or interpreters. You can also import data to MS Excel, MS access, Labview or Agilent VEE. The Visual Basic example is a small testing programm which allows you to check all relevant functions of the card. Additionally it is a good starting point for own projects.

It is possible to employ the card in all applications which are able to call an external DLL function because QLIB is an API and has its programming port in DLL.

You can use the same instructions on all supported operating systems. If you created an application on WIndows 95 you can immediatly use it on Windows XP.

The driver of Linux contains also an software port which is very close to QLIB. You can compile your Windows examples without having any problems under Linux.

USBOPTO64IN is also available as USBOPTO64OUT and USBREL64 .

•General I/O
Dimensions: 254*105*57 mm
Power Supply: 5V USB or 12V-24V external

•Inputs
Quantity: 64 galvanically isolated Optocouppler Inputs
Input Current: max. 20mA
Input Voltage: 12V-30V opt. 5V-12V

•Bus
USB

•Temperature Range
0...50 °C



Manual for the USB Flasher
PDF manual for the Firmware Update Programm
[Download 281.7KB]


Manual for USB, ETH and SER Optocoupler and Relay Modules
This is the manual for our optocoupler and relay modules.
[Download 1898.8KB]



QCLI (QUANCOM Command Line Interface)
The QUANCOM Command Line Interface (QCLI) was made for all those which don´t have programming experience or knowledge.

It is a simple command line tool which makes it able to control our I/O and Watchdog boards with some very simple strings.

Note that this procedure is not as fast as a programm written in a higher programmiung language, for example C.
[Download 56KB]


Command Line Tool to Change Module Address
This command line tool makes it possible to change the address of your module by software.

Note that therefore the installed Firmware has to be higher or equal to Version 1.30 and the switch in the QLIB Configuration Utility must be set correctly.
[Download 35.4KB]


QCLI (QUANCOM Command Line Interface)
Das Quancom Command Line Interface (QCLI) ist für diejenigen gedacht, die sich in der Programmierwelt nicht zurechtfinden, oder auch keine Lust haben sich ein eigenes Programm für den Zugriff auf unsere QUANCOM Karten zu schreiben. Da das QCLI recht simpel gehalten ist, ist es um ein wesentliches langsamer, verglichen zu einem gut programmierten Programm. Mit einfachen Funktionen der QAPI lassen sich über das QCLI QUANCOM Karten und Module bedienen und konfigurieren. [Download 32.1KB]


Firmware Version 1.56
Current firmware for QUANCOM USB-, ETH- & SER modules

 USB Flasher Guide

Caution: This firmware is not to be used with the following modules
  • USBGPIB1
  • USBCOUNTER1
  • USBCPU1
  • USBREL8UM
  • USBREL8 & /LC
  • USBOPTO8 & /LC
[Download 27.6KB]


Firmware Version 1.34
Firmware for QUANCOM USB-, ETH- & SER modules

 USB Flasher Guide

Caution: This firmware is not to be used with the following modules
  • USBGPIB1
  • USBCOUNTER1
  • USBCPU1
  • USBREL8UM
  • USBREL8 & /LC
  • USBOPTO8 & /LC
[Download 20.7KB]


QCLI QUANCOM Command Line Interface
( Windows Executable )

QUANCOM QCLI provides the user with a simple to use command line tool to control QUANCOM hardware.

[ Further Information to QCLI ]

[ Online-Documentation to QCLI ]

[Download 56KB]



Hutschiene
Top-Hat Rail


NT12V/3A
Compact power supply


NT12V/3A
Compact power supply


NT24V/2A
Compact power supply


  Add to cart
Price
544.04 Euro
(incl. Taxes)

Operating Systems
Windows 10/8/7 (32/64)
Windows Vista (32/64)
Windows XP (32/64)
Windows 2000
Win Server 2008/2012 (32/64)
Win 2003 Server (32/64)
Win 2000 Server
Windows 95/98/Me
Linux
Similar Products
 
ETHOPTO32IO

Ethernet Interface
32 Optocoupler Inputs
32 Optocoupler Outputs
 
USBOPTO16IO

16 Optocoupler Inputs
16 Optocoupler Outputs
Tough Metal Case
 
USBOPTO32IO

32 Optocoupler Inputs
32 Optocoupler Outputs
Tough Metal Case





... back to home




Updated on 13.6.2015 by Michael Reimer